Hi Michael,
Thanks for your question. Please give us a call on 01403 21204 and our customer service team be able to point you in the right direction.
Easy to Install
Fast and Effective
>40% Energy Saving
Ultrotherm is supplied as convenient, flexible tiles that allow it to be installed around awkward shapes and curves. Ultrotherm tiles are simply stuck onto prepared walls using Ultrotherm Adhesive. Once applied, the Ultrotherm Tiles can simply be plastered over to create a wall surface ready for decoration - e.g. using Dryzone System Mould Resistant Paint.
Accessories such as trim beads are available to simplify installation around skirting boards, coving, and window reveals.
Mould growth caused by condensation is a major problem in the UK. The primary methods of preventing it are increasing the surface temperatures of walls and improving ventilation.
Installation of the Ultrotherm System increases the surface temperature of walls by insulating them - therefore reducing the risk of condensation. In most cases the installation of the Ultrotherm System will be enough to prevent condensation and mould growth. However it can also be used in conjunction with Dryzone Anti-Mould Emulsion Paint and ventilation measures such as Humidistat Fans.
Ultrotherm System Components
Ultrotherm 12 mm thick tiles. Each tile measures 1000 × 500 mm. Supplied in packs of 10 (covering 5 m2)
Ultrotherm 8 mm thick reveal tiles (for insulating window and door reveals). Each tile measures 1000 × 230 mm. Supplied in packs of 5 (covering 1.15 m2)
Ultrotherm Adhesive. Used for bonding Ultrotherm tiles. Supplied in 500 ml Spray (covers up to 2.5 m2 ) and 10 kg tubs (covers up to 10 m2)
Ultrotherm Insulated Plastic Trim Beads. For use around window and door frames to reduce cold bridging. Also allow windows and doors to be replaced without damaging the insulation system. Supplied in 2.5 m lengths.
Ultrotherm Plastic Angle Beads. For use around all external angles. Supplied in 2.5 m lengths.
Dryzone System Anti-Mould Emulsion Paint. High performance mould resistant emulsion paint recommended for use when decorating over the Ultrotherm System in rooms susceptible to condensation and mould growth. Supplied in 5 litre cans.
0 Reviews
0 Reviews
3 Reviews
0 ReviewsHi Michael,
Thanks for your question. Please give us a call on 01403 21204 and our customer service team be able to point you in the right direction.
Hi, my house was built in 1902, it is a solid detached brick building with no cavity. During the winter, there is condensation, mold growth, cold and damp spots on the walls, especially around the bay bedroom window frames and on the chimney breast. What is the best and most cost effective solution for this problem.. Many thanks for your kind attention. Linda
Hi Linda,
Thanks for your question.
To solve your home's damp issues, it is important to make sure that the window frames and chimney breast are both in good condition - with no damage, gaps or weaknesses in the chimney masonry and window frames themselves. Ensure that there are no gutter defects or damage to the exterior wall masonry that may be allowing rain into the solid wall. Consideration should also be given to appropriate central heating and ventilation for the cold weather.
After this, a variety of options can be considered, including Stormdry Masonry Protection Cream to waterproof the exterior masonry, Ultrotherm or Stormdry EP-Board internal insulation to keep the interior warm. A selection of Dryzone anti-mould treatments may also be suitable, as long as the underlying cause of condensation has been rectified.
Please give us a call on 01403 210204 so we can advise you further. Alternatively, email us at info@safeguardeurope.com with as much information as possible. Some photos would also be helpful to allow our technical team to diagnose the issue accurately.
Subscribe to get information about products and offers.
Do you have a list of approved Ultrottherm installers for the Epsom Surrey area?