Drybase TS-Plus Tanking Slurry
Approx. 30 mins
4–6 hours
≤ 0.5 kg/m2·h0.5
Drybase TS-PLUS Tanking Slurry is a cementitious tanking slurry that acts as a barrier to moisture and salts onto prepared concrete and masonry. This tightly bonding slurry is suitable for horizontal and vertical surfaces. It is resistant to frost and heat after setting, but also permeable to vapour. Durable enough for use as a tanking layer in domestic and commercial applications.
Good afternoon,
Thank you for reaching out to us about our Drybase TS-Plus Tanking Slurry.
A single 20 kg bag typically covers between 3.5 and 5 m². This coverage is based on applying two coats, each 1 to 2 mm thick, resulting in a total finished thickness of 2 to 4 mm.
I hope this helps. If you have any other questions or need further assistance, please feel free to ask—we're always happy to help.
Best regards,
Kelsey
Safeguard Europe Ltd
Would it be safe (and effective) to use on the inside of raised beds built of dense hollow concrete blocks that will be used to grow vegetables for human consumption?
Good afternoon,
Thank you for your question.
Drybase® TS-PLUS Tanking Slurry is a cementitious tanking slurry, as a cement based product this is alkaline so we would suggest allowing the product time to fully dry and cure before filling with soil and planting.
I hope this helps and if you have any further questions, please let us know.
Kind regards,
Teigan
Safeguard Europe Ltd.
01403210204.
Can this material be used on the inside of a habitable dwelling? (35m2 area)
Thanks
Andy
Good afternoon,
Thank you for your question.
Drybase® TS-PLUS Tanking Slurry can be used to create a moisture and salt barrier on internal walls, for above ground waterproofing.
Surfaces treated with Drybase® TS-PLUS Tanking Slurry can have a plaster or render finish applied, it may be necessary to apply
a thin rough cast of sand and cement onto the final Drybase® TS-PLUS Tanking Slurry surface. This can be done when Drybase® TS-PLUS Tanking Slurry has reached the initial set, usually between 2 – 4 hours.
If you have any further questions regarding application and finishes, please contact us directly on 01403210204.
I hope this helps.
Kind regards,
Teigan
Safeguard Europe Ltd.
01403210204.
Hi - Could you let us know if it is better to use 'Drybase Tanking Slurry' or 'Drybase TS-Plus Tanking Slurry' to a wall below the line of a
physical or chemical DPC please?
Hello,
Thank you for your enquiry.
Drybase TS-Plus Tanking Slurry is suitable for above ground waterproofing and lower ground areas up to 600mm depth.
If you do need to use the product at a deeper level below ground you can mix it with our Drybase 5-bar Waterproofer or alternatively you could use the Drybase Tanking Slurry.
If you have any further queries please do not hesitate to get in touch.
Damp proofing needed on internal cotswold stone walls. I'm thinking of using Dryzone cream as a DPC and then Hi Lime plaster with a skim coat of finish plaster. However, if DPC is unreliable, should I use a TS tanking slurry behind the Hi Lime Plaster?
Hi Jonathan,
Thank you for your question.
As long as the wall is in a sound condition then the Dryzone DPC Cream and Hi-Lime Plaster should be more than effective for treating rising damp. However if you are considering using TS PLUS as part of a belts and braces approach then this will also be an effective alternative for preventing damp from coming through on to the plaster.
If you have any further queries please feel free to give us a call on 01403 210204.
Is Drybase TS-Plus suitable for repairing cracks in a concrete pond?
The small print on the packaging states that when mixed with water it becomes corrosive.
This begs a few questions: First how persistent is the corrosive effect. second Is the toxicity sufficient to affect aquatics if used to repair cracks in pond concrete?
Hi Les,
Thanks for your question. We recommend mixing Drybase TS-PLUS with Drybase 5-Bar Waterproofer for ponds.
Once TS-PLUS has set (as with any cementitious coating), it is no longer corrosive to bare skin.
Once applied, you must allow the coating to fully cure over 7-28 days, then wash the finished surface to remove any residue before refilling the pond.
If you have any further questions, please get in touch via 01403 210204 so we can advise you further.
Subscribe to get information about products and offers.
I want to use the Drybase TS-Plus Tanking Slurry, can you advise as to the coverage per bag?